Author Topic: Dragon tower bridge part  (Read 2714 times)

Offline kenc

  • Playmo Lover
  • ***
  • Posts: 289
  • Gender: Male
Dragon tower bridge part
« on: December 09, 2010, 08:30:26 »
Hi folks, I have a question again about the stone bridge part 30 20 4742 that joins the two round towers of the large dragon castle 4835. Could someone tell me the length of that part? I need to know if it fits on one of my constructions.

Many thanks in advance  :wave:  :wave:

Offline Wolf Knight

  • Playmo Guru
  • ******
  • Posts: 11186
  • Gender: Male
Re: Dragon tower bridge part
« Reply #1 on: December 09, 2010, 21:46:12 »
Hi!

thats 3,5 inches or 8,3 cm!


Offline kenc

  • Playmo Lover
  • ***
  • Posts: 289
  • Gender: Male
Re: Dragon tower bridge part
« Reply #2 on: December 10, 2010, 07:33:57 »
Thanks a lot, Panos!!   :wave::) That's unfortunately 0,7cm too short for proper use with system-x scaled parts  :(  :( But I'll give it a shot anyway  ;D

They're for connecting buttresses to my cathedral.

Offline Wolf Knight

  • Playmo Guru
  • ******
  • Posts: 11186
  • Gender: Male
Re: Dragon tower bridge part
« Reply #3 on: December 10, 2010, 11:25:02 »
Thanks a lot, Panos!!   :wave::) That's unfortunately 0,7cm too short for proper use with system-x scaled parts  :(  :( But I'll give it a shot anyway  ;D

They're for connecting buttresses to my cathedral.

I got the impression they would!  ;) Its not easy to place them on system x, as each side has a different clip on end... I'll take a picture of it once I get home to show you what I mean!

Offline kenc

  • Playmo Lover
  • ***
  • Posts: 289
  • Gender: Male
Re: Dragon tower bridge part
« Reply #4 on: December 10, 2010, 13:56:48 »
That would be great if you could show me a picture  8-) ! At least I managed to attach the gargoyles with bluetac. I intend to do the same with the bridge parts...

Greetings,

Ken

Offline basilsdad

  • Playmo Master
  • *****
  • Posts: 1887
  • Gender: Male
Re: Dragon tower bridge part
« Reply #5 on: December 10, 2010, 16:11:56 »
This sounds like a really neat project, good luck with it.
Joe
"One cat just leads to another."
 - Ernest Hemingway

Offline Wolf Knight

  • Playmo Guru
  • ******
  • Posts: 11186
  • Gender: Male
Re: Dragon tower bridge part
« Reply #6 on: December 10, 2010, 17:38:55 »
Hey Ken! Here are a few pics!

As you see, each side is different...still if you use bluetac, you can cut the staight line connection side, and bluetaced it on the wall...

Offline Wolf Knight

  • Playmo Guru
  • ******
  • Posts: 11186
  • Gender: Male
Re: Dragon tower bridge part
« Reply #7 on: December 10, 2010, 17:40:31 »
and one more...

btw, the pattern on it is a sticker, not a print-on.

Offline kenc

  • Playmo Lover
  • ***
  • Posts: 289
  • Gender: Male
Re: Dragon tower bridge part
« Reply #8 on: December 13, 2010, 07:49:49 »
and one more...

btw, the pattern on it is a sticker, not a print-on.

That's pro-active replying  ;)  ;) My next question would have been if the pattern was a printon or a sticker. Glad it's a sticker. I think this part will do the trick. Thanks again for the pics, Panos!

Offline Wolf Knight

  • Playmo Guru
  • ******
  • Posts: 11186
  • Gender: Male
Re: Dragon tower bridge part
« Reply #9 on: December 13, 2010, 08:06:49 »
Any time Ken  :wave: